- Maison
- Fils d'alimentation
- Acheter Leads
- A propos de nous
- Produits
- Nouvelles
- Honneurs
- Message
- Contacter
- Les catégories de produit
- Liens amicaux
Nom de l'information: | 4-way switch intelligente entra?nement |
Publié: | 2015-04-07 |
Validité: | 0 |
Caractéristiques: | |
Quantité: | 1000.00 |
Description Prix: | |
Description détaillée du produit: | Sheng Tai (approvisionnement) ventes de smart quatre voies la production en série de commande de commutateur, pour le contr?le d'éclairage automatisé, les systèmes de gestion de l'éclairage à distance, la gestion d'identification faire un éclairage plus économe en énergie, plus facile à contr?ler, pour maximiser l'efficacité! Années d'expérience, le grand nombre de consommateurs la reconnaissance ............ I. Présentation ST12.16.1 module de commutation intelligent, bus de communication 485, est livré avec la section de contr?le de la scène, qui ont leurs propres relais passer commande manuelle, avec des capacités de programmation et de gestion à distance . Deuxièmement, les caractéristiques fonctionnelles 1,12 relais unité de sortie de l'interrupteur 2. Le contr?leur de scène est livré avec jusqu'à 128 scènes 3. Chaque boucle dispose d'un délai de protection d'éclairage (0-60 minutes) 4. Chaque boucle a une ouverture partielle retard (0-25 secondes) 5. Chaque commutateur de relais boucle 6. peut être commandé manuellement avec des capacités de programmation et de gestion à distance 7. Redémarrez équipement facultatif a été ouvert scène ou spécifiée scène 8. 9. communiquent par une norme 485 35mm ferroviaire structure de montage Principaux paramètres techniques 1. Tension d'entrée: DC24V consommation d'énergie 2. de bus: 35mA / DC24V 3. Interrupteur circuit: 12 Route 4. Chaque circuit de commutation maximum actuel: 16A 5. Relais de vie électrique: plus de 60 000 fois (charge résistive) 6. Conditions environnementales: température 0 ℃ ~ 45 ℃ Humidité relative 20% ~ 90% Température de stockage -40 ℃ ~ + 55 ℃ humidité relative de stockage de 10% à 93% 7. Dimensions de fonctionnement: 165mm × 88mm × 66mm 8. Poids: 0,6 kg Quatrièmement, l'apparence et l'apparition de module explication schéma de cablage est comme suit: ① 1,2,3,4,5,6,7,8,9,10,11,12 interrupteur 12 relais L'indicateur de la boucle du circuit de sortie. 12 feux et 12 correspondent respectivement au bouton manuel du commutateur, chaque indicateur montre l'état du circuit de commutation correspondante. ③ 1,2,3,4,5,6,7,8,9,10,11,12 12 relais touche manuelle après chaque pression, le relais état avec l'état actuel de la face. ④ Lorsque l'alimentation et de la lumière inhabituelle, lorsque le module fonctionne correctement, le voyant clignote une fois par seconde (clignotement lent), des conditions anormales, le voyant clignote une fois (flash) toutes les 250ms. ⑤ DC +, DATA +, DATA-, COM 485 bus définitions de signal de la borne de raccordement et de la correspondance entre le 485-cablé pour: DC + (+ 24V) → brun, orange Data + (le signal +) → bleu, DATA- vert (le signal - ) → bleu, vert et blanc COM (Common) → blanc, orange et blanc ⑥ brun interface de signal d'incendie. DI, DI + pour l'interface d'entrée du signal d'incendie, DO-, DO + interface de sortie de rétroaction pour le feu. Les deux interfaces sont signal actif, doivent avoir accès externe au pouvoir, di-, DI + permet seulement la gamme de tension d'entrée DC est DC5V-30V; DO-, DO + permet également seulement une gamme de tension d'entrée DC est DC5V-30V, avec conduite relais DC12V, DC24V et d'autres équipements, qui tous deux ne ont pas accès à un signal 220V AC, afin d'éviter d'endommager l'équipement. Quand le feu de signal d'entrée par défaut du système, déclenchant tous les circuits interface ouverte, sortie de retour connecté; lorsque le signal de feu est rétabli, restaurer l'état d'origine du circuit, l'interface de sortie de rétroaction est déconnecté; signaux ci-dessus peuvent être programmés pour déclencher une scène changements. Cinquièmement, installation et connexion 1. conditions d'installation à ventiler emplacement d'installation, faites attention à l'humidité, aux chocs et à la poussière. 2. spécifications de cablage l Ce module relais passer le cable de sortie: cuivre 2.5mm2 cable l 485 cable de bus: le super paire cinq fils ou 4 fils torsadés 3. Des systèmes typiques sont généralement connectés au système est reliée au module (élément de référence), comme illustré ci-dessous. Permet de connecter des dispositifs de commande de commutateur, contr?le d'éclairage (y compris le contr?le de la scène, etc.) via le panneau de contr?le 485, les serveurs de gestion du système, la gestion des systèmes, et la connexion avec d'autres systèmes de contr?le et ainsi de suite. Six, les fonctions et les instructions d'un commutateur de relais de contr?le manuel du module en plus de recevoir un signal externe de commande de commutation, peut également être interrupteur commandé manuellement. En faisant fonctionner un circuit de relais 12 de commande manuelle, qui peut commander les circuits de 1 à 12 sous et hors tension. 2, le nombre d'ID d'ordinateur sur le dispositif doit être paramètres "Logiciel de contr?le système SILO", prévues pour voir les instructions du logiciel. 3, Scène jusqu'à 128 scènes, chaque scène est une combinaison de la boucle ensemble. Scène doit passer "le logiciel de contr?le du système de SILO" pour régler, voir les paramètres du logiciel. 4, en boucle ouverte et en boucle ouverte retard de protection retard: Chaque boucle peut être réglé pour activer retard, la boucle de démarrage après que, pour atteindre la boucle uniquement lorsque la valeur de la sortie du retard. Effet sur le retard, tandis que lancer simultanément plusieurs boucles, boucle départ suivi par la valeur de retard pour éviter l'impact de courant à haute tout a commencé. Remarque: sur les valeurs de retard allant de 0,0 à 25,0 secondes. Circuit de retard de protection: Chaque boucle peut être mis en place pour protéger le retard, qui est, quand une sortie de circuit se éteint, afin de protéger la charge, seulement la temporisation de protéger la valeur de la sortie de la boucle ne peut plus être contr?lée. Remarque: Les valeurs de retard de protection allant de 00 à 60 points. Sur la valeur de retard, de protéger la valeur de retard doit être réglé par "logiciel de contr?le du système de SILO", réglez réfléchie instructions. 5. Le champ est mis à courir après (scénarios puissance de valorisation fixés) de redémarrage que le système mis à ouvrir le champ, après le redémarrage de la machine se déroulera la dernière scène quand il est éteint. Après le système est configuré pour le champ spécifié, la machine redémarre, se déroulera la scène spécifiée. Définit par "logiciel de contr?le du système de SILO", ensemble reflètent instructions. Le scénario par défaut ne fonctionne pas après le redémarrage. Utilisation s?re et entretien de l'autobus ne peuvent pas être inférieur à 1,485 16V, sinon le relais ne fonctionne pas. 2. Chaque boucle doit accéder AC220V ~ 240V alimentation à travers le disjoncteur approprié. 3. Afin de garantir l'utilisation de relais, devraient noter les points suivants: l Pour connecter une charge résistive, le courant de chaque boucle de charge peut être jusqu'à 16A. l Pour la connexion de charges inductives (haute tension), connecter la charge capacitive (avec l'impact du courant), chaque circuit doit être inférieur au courant de charge maximum de 16A. Charge convenable taille réelle spécifique du facteur de puissance de la charge, sélectionné en fonction de la plus faible du facteur de puissance, plus la charge sélectionnée. l en particulier pour une faible charge du facteur de puissance est connecté, tels que les lampes à économie d'énergie de faible facteur de puissance, lampes à ballast électronique à faible facteur de puissance, etc., en raison de l'impact du courant, afin de protéger le relais de sécurité utilisé doit être approprié de réduire la charge, afin de réduire l'impact du courant. 4. Ne fermez pas à l'équipement de brouillage. 5. Pour établir un bon environnement de ventilation. 6. Lors de l'utilisation, faites attention à l'humidité, aux chocs et à la poussière. 7. Lorsque la machine échoue, contactez un personnel qualifié de service ou de la Société. ST8.16.1 module de commutation intelligente utilise un module de commutation intelligente manuel sur les lignes de ST8.16.1, le bus de communication 485, livré avec la section de contr?le de la scène, qui ont leurs propres relais passer commande manuelle, avec des capacités de programmation et de gestion à distance. Deuxièmement, les caractéristiques 1.8 canaux unité de sortie de relais 2. Le commutateur est livré avec un contr?leur de scène, jusqu'à 128 scènes 3. Chaque boucle dispose d'un délai de protection d'éclairage (0-60 minutes) 4. Chaque boucle a une ouverture partielle retard (0-25 secondes) 5. Chaque commutateur de relais boucle 6. peut être commandé manuellement avec des capacités de programmation et de gestion à distance 7. Redémarrez équipement facultatif a été ouvert scène ou spécifiée scène 8. 9. communiquent par une norme 485 35mm ferroviaire structure de montage Principaux paramètres techniques 1. Tension d'entrée: DC24V consommation d'énergie 2. de bus: 30 mA / DC24V 3. circuit de commutation: 8 4. Chaque circuit de commutation maximales actuelles: 16A 5. Relais vie électrique: plus de 60 000 fois (charge résistive) 6. Conditions environnementales: température 0 ℃ ~ 45 ℃ Humidité relative 20% ~ 90% Température de stockage -40 ℃ ~ + 55 ℃ humidité relative de stockage de 10% à 93% 7. Dimensions de fonctionnement: 165mm × 88mm × 66mm 8. Poids: 0,5 kg Quatrièmement, l'apparence et l'apparition de module explication schéma de cablage est comme suit: ① 1,2,3,4,5,6,7,8 total de huit relais commute le circuit de sortie ② indicateur de circuit. 8 LED et 8 correspondent respectivement au bouton manuel du commutateur, chaque indicateur montre l'état du circuit de commutation correspondante. ③ 1,2,3,4,5,6,7,8 total de huit touche manuelle relais après chaque pression, le relais état avec l'état actuel de la face. ④ Lorsque l'alimentation et de la lumière inhabituelle, lorsque le module fonctionne correctement, le voyant clignote une fois par seconde (clignotement lent), des conditions anormales, le voyant clignote une fois (flash) toutes les 250ms. ⑤ DC +, DATA +, DATA-, COM 485 bus définitions de signal de la borne de raccordement et de la correspondance entre le 485-cablé pour: DC + (+ 24V) → brun, orange Data + (le signal +) → bleu, DATA- vert (le signal - ) → bleu, vert et blanc COM (Common) → blanc, orange et blanc ⑥ brun interface de signal d'incendie. DI, DI + pour l'interface d'entrée du signal d'incendie, DO-, DO + interface de sortie de rétroaction pour le feu. Les deux interfaces sont signal actif, doivent avoir accès externe au pouvoir, di-, DI + permet seulement la gamme de tension d'entrée DC est DC5V-30V; DO-, DO + permet également seulement une gamme de tension d'entrée DC est DC5V-30V, avec conduite relais DC12V, DC24V et d'autres équipements, qui tous deux ne ont pas accès à un signal 220V AC, afin d'éviter d'endommager l'équipement. Quand le feu de signal d'entrée par défaut du système, déclenchant tous les circuits interface ouverte, sortie de retour connecté; lorsque le signal de feu est rétabli, restaurer l'état d'origine du circuit, l'interface de sortie de rétroaction est déconnecté; signaux ci-dessus peuvent être programmés pour déclencher une scène changements. Cinquièmement, installation et connexion 1. conditions d'installation à ventiler emplacement d'installation, faites attention à l'humidité, aux chocs et à la poussière. 2. spécifications de cablage l Ce module relais passer le cable de sortie: cuivre 2.5mm2 cable l 485 cable de bus: le super paire cinq fils ou 4 fils torsadés 3. Des systèmes typiques sont généralement connectés au système est reliée au module (élément de référence), comme illustré ci-dessous. Permet de connecter des dispositifs de commande de commutateur, contr?le d'éclairage (y compris le contr?le de la scène, etc.) via le panneau de contr?le 485, les serveurs de gestion du système, la gestion des systèmes, et la connexion avec d'autres systèmes de contr?le et ainsi de suite. Six, les fonctions et les instructions d'un commutateur de relais de contr?le manuel du module en plus de recevoir un signal externe de commande de commutation, peut également être interrupteur commandé manuellement. 1-8 boucle à travers le fonctionnement de l'interrupteur manuel à relais, qui peut commander une boucle et à l'extérieur 8.1. 2, le nombre d'ID d'ordinateur sur le dispositif doit être paramètres "Logiciel de contr?le système SILO", prévues pour voir les instructions du logiciel. 3, Scène jusqu'à 128 scènes, chaque scène est une combinaison de la boucle ensemble. Scène doit passer "le logiciel de contr?le du système de SILO" pour régler, voir les paramètres du logiciel. 4, en boucle ouverte et en boucle ouverte retard de protection retard: Chaque boucle peut être réglé pour activer retard, la boucle de démarrage après que, pour atteindre la boucle uniquement lorsque la valeur de la sortie du retard. Effet sur le retard, tandis que lancer simultanément plusieurs boucles, boucle départ suivi par la valeur de retard pour éviter l'impact de courant à haute tout a commencé. Remarque: sur les valeurs de retard allant de 0,0 à 25,0 secondes. Circuit de retard de protection: Chaque boucle peut être mis en place pour protéger le retard, qui est, quand une sortie de circuit se éteint, afin de protéger la charge, seulement la temporisation de protéger la valeur de la sortie de la boucle ne peut plus être contr?lée. Remarque: Les valeurs de retard de protection allant de 00 à 60 points. Sur la valeur de retard, de protéger la valeur de retard doit être réglé par "logiciel de contr?le du système de SILO", réglez réfléchie instructions. 5. Le champ est mis à courir après (scénarios puissance de valorisation fixés) de redémarrage que le système mis à ouvrir le champ, après le redémarrage de la machine se déroulera la dernière scène quand il est éteint. Après le système est configuré pour le champ spécifié, la machine redémarre, se déroulera la scène spécifiée. Définit par "logiciel de contr?le du système de SILO", ensemble reflètent instructions. Le scénario par défaut ne fonctionne pas après le redémarrage. Utilisation s?re et entretien de l'autobus ne peuvent pas être inférieur à 1,485 16V, sinon le relais ne fonctionne pas. 2. Chaque boucle doit accéder AC220V ~ 240V alimentation à travers le disjoncteur approprié. 3. Afin de garantir l'utilisation de relais, devraient noter les points suivants: l Pour connecter une charge résistive, le courant de chaque boucle de charge peut être jusqu'à 16A. l Pour la connexion de charges inductives (haute tension), connecter la charge capacitive (avec l'impact du courant), chaque circuit doit être inférieur au courant de charge maximum de 16A. Charge convenable taille réelle spécifique du facteur de puissance de la charge, sélectionné en fonction de la plus faible du facteur de puissance, plus la charge sélectionnée. l en particulier pour une faible charge du facteur de puissance est connecté, tels que les lampes à économie d'énergie de faible facteur de puissance, lampes à ballast électronique à faible facteur de puissance, etc., en raison de l'impact du courant, afin de protéger le relais de sécurité utilisé doit être approprié de réduire la charge, afin de réduire l'impact du courant. 4. Ne fermez pas à l'équipement de brouillage. 5. Pour établir un bon environnement de ventilation. 6. Lors de l'utilisation, faites attention à l'humidité, aux chocs et à la poussière. 7. Lorsque la machine échoue, contactez un personnel qualifié de service ou de la Société. ST6.16.1 module de commutation intelligente utilise un module de commutation intelligente manuel sur les lignes de ST6.16.1, le bus de communication 485, livré avec la section de contr?le de la scène, qui ont leurs propres relais passer commande manuelle, avec des capacités de programmation et de gestion à distance. Deuxièmement, les caractéristiques 1.6 canaux unité de sortie de relais 2. Le commutateur est livré avec un contr?leur de scène, jusqu'à 128 scènes 3. Chaque boucle dispose d'un délai de protection d'éclairage (0-60 minutes) 4. Chaque boucle a une ouverture partielle retard (0-25 secondes) 5. Chaque commutateur de relais boucle 6. peut être commandé manuellement avec des capacités de programmation et de gestion à distance 7. Redémarrez équipement facultatif a été ouvert scène ou spécifiée scène 8. 9. communiquent par une norme 485 35mm ferroviaire structure de montage Principaux paramètres techniques 1. Tension d'entrée: DC24V 2. bus consommation d'énergie: 20 mA / DC24V 3. circuit de commutation: 6 Route 4. Chaque circuit de commutation maximum actuel: 16A 5. Relais vie électrique: plus de 60 000 fois (charge résistive) 6. Conditions environnementales: température 0 ℃ ~ 45 ℃ Humidité relative 20% ~ 90% Température de stockage -40 ℃ ~ + 55 ℃ humidité relative de stockage de 10% à 93% 7. Dimensions de fonctionnement: 108mm × 88mm × 66mm 8. Poids: 0,4 kg Quatrièmement, l'apparence et l'apparition de module explication schéma de cablage est comme suit: ① 1,2,3,4,5,6 borne de sortie de circuit de commutation 6 relais ② indicateur de circuit. 6 LED et 6 correspondent respectivement au bouton manuel du commutateur, chaque indicateur montre l'état du circuit de commutation correspondante. ③ 1,2,3,4,5,6 6 relais touche manuelle après chaque pression, le relais état avec l'état actuel de la face. ④ Lorsque l'alimentation et de la lumière inhabituelle, lorsque le module fonctionne correctement, le voyant clignote une fois par seconde (clignotement lent), des conditions anormales, le voyant clignote une fois (flash) toutes les 250ms. ⑤ DC +, DATA +, DATA-, COM 485 bus définitions de signal de la borne de raccordement et de la correspondance entre le 485-cablé pour: DC + (+ 24V) → brun, orange Data + (le signal +) → bleu, DATA- vert (le signal - ) → bleu, vert et blanc COM (Common) → blanc, orange et blanc ⑥ brun interface de signal d'incendie. DI, DI + pour l'interface d'entrée du signal d'incendie, DO-, DO + interface de sortie de rétroaction pour le feu. Les deux interfaces sont signal actif, doivent avoir accès externe au pouvoir, di-, DI + permet seulement la gamme de tension d'entrée DC est DC5V-30V; DO-, DO + permet également seulement une gamme de tension d'entrée DC est DC5V-30V, avec conduite relais DC12V, DC24V et d'autres équipements, qui tous deux ne ont pas accès à un signal 220V AC, afin d'éviter d'endommager l'équipement. Quand le feu de signal d'entrée par défaut du système, déclenchant tous les circuits interface ouverte, sortie de retour connecté; lorsque le signal de feu est rétabli, restaurer l'état d'origine du circuit, l'interface de sortie de rétroaction est déconnecté; signaux ci-dessus peuvent être programmés pour déclencher une scène changements. Cinquièmement, installation et connexion 1. conditions d'installation à ventiler emplacement d'installation, faites attention à l'humidité, aux chocs et à la poussière. 2. spécifications de cablage l Ce module relais passer le cable de sortie: cuivre 2.5mm2 cable l 485 cable de bus: le super paire cinq fils ou 4 fils torsadés 3. Des systèmes typiques sont généralement connectés au système est reliée au module (élément de référence), comme illustré ci-dessous. Permet de connecter des dispositifs de commande de commutateur, contr?le d'éclairage (y compris le contr?le de la scène, etc.) via le panneau de contr?le 485, les serveurs de gestion du système, la gestion des systèmes, et la connexion avec d'autres systèmes de contr?le et ainsi de suite. Six, les fonctions et les instructions d'un commutateur de relais de contr?le manuel du module en plus de recevoir un signal externe de commande de commutation, peut également être interrupteur commandé manuellement. 1-6 en faisant fonctionner le circuit de commutation de relais manuel, qui permet de contr?ler les circuits 1-6 et à l'extérieur. 2, le nombre d'ID d'ordinateur sur le dispositif doit être paramètres "Logiciel de contr?le système SILO", prévues pour voir les instructions du logiciel. 3, Scène jusqu'à 128 scènes, chaque scène est une combinaison de la boucle ensemble. Scène doit passer "le logiciel de contr?le du système de SILO" pour régler, voir les paramètres du logiciel. 4, en boucle ouverte et en boucle ouverte retard de protection retard: Chaque boucle peut être réglé pour activer retard, la boucle de démarrage après que, pour atteindre la boucle uniquement lorsque la valeur de la sortie du retard. Effet sur le retard, tandis que lancer simultanément plusieurs boucles, boucle départ suivi par la valeur de retard pour éviter l'impact de courant à haute tout a commencé. Remarque: sur les valeurs de retard allant de 0,0 à 25,0 secondes. Circuit de retard de protection: Chaque boucle peut être mis en place pour protéger le retard, qui est, quand une sortie de circuit se éteint, afin de protéger la charge, seulement la temporisation de protéger la valeur de la sortie de la boucle ne peut plus être contr?lée. Remarque: Les valeurs de retard de protection allant de 00 à 60 points. Sur la valeur de retard, de protéger la valeur de retard doit être réglé par "logiciel de contr?le du système de SILO", réglez réfléchie instructions. 5. Le champ est mis à courir après (scénarios puissance de valorisation fixés) de redémarrage que le système mis à ouvrir le champ, après le redémarrage de la machine se déroulera la dernière scène quand il est éteint. Après le système est configuré pour le champ spécifié, la machine redémarre, se déroulera la scène spécifiée. Définit par "logiciel de contr?le du système de SILO", ensemble reflètent instructions. Le scénario par défaut ne fonctionne pas après le redémarrage. Utilisation s?re et entretien de l'autobus ne peuvent pas être inférieur à 1,485 16V, sinon le relais ne fonctionne pas. 2. Chaque boucle doit accéder AC220V ~ 240V alimentation à travers le disjoncteur approprié. 3. Afin de garantir l'utilisation de relais, devraient noter les points suivants: l Pour connecter une charge résistive, le courant de chaque boucle de charge peut être jusqu'à 16A. l Pour la connexion de charges inductives (haute tension), connecter la charge capacitive (avec l'impact du courant), chaque circuit doit être inférieur au courant de charge maximum de 16A. Charge convenable taille réelle spécifique du facteur de puissance de la charge, sélectionné en fonction de la plus faible du facteur de puissance, plus la charge sélectionnée. l en particulier pour une faible charge du facteur de puissance est connecté, tels que les lampes à économie d'énergie de faible facteur de puissance, lampes à ballast électronique à faible facteur de puissance, etc., en raison de l'impact du courant, afin de protéger le relais de sécurité utilisé doit être approprié de réduire la charge, afin de réduire l'impact du courant. 4. Ne fermez pas à l'équipement de brouillage. 5. Pour établir un bon environnement de ventilation. 6. Lors de l'utilisation, faites attention à l'humidité, aux chocs et à la poussière. 7. Lorsque la machine échoue, contactez un personnel qualifié de service ou de la Société. TLC3.1.1 module de synchronisation logique manuel I. module de synchronisation Présentation logique, intégrée dans les scènes et le calendrier, de sorte que le module sur le bus selon une fonction de contr?le automatique pré-établi une bonne date et l'heure automatiquement exécuter un scénario, aucun logiciel de contr?le de fond, vous pouvez obtenir . Construit en fonction de synchronisation de haute précision de la latitude et la longitude, l'emplacement de l'appareil peut automatiquement selon la latitude et la longitude, pour calculer les heures de lever et coucher du soleil tous les jours, et de déclencher la scène approprié, cette fonction est particulièrement adapté pour la construction, l'éclairage extérieur et de la rue contr?le automatique et d'autres applications. Deuxièmement, l'interface Caractéristiques 1. E-BUS avec haut-128 scènes 2. 3. 4. Built-in minuterie de haute précision 128 5. 6. Latitude capacités de gestion de temps de réseau de synchronisation avec programmation à distance et la relecture 7. 10M / 100M Ethernet 8. rail de 35mm de norme d'interface structure de montage Principaux paramètres techniques 1. Tension d'entrée: DC24V 2. Bus consommation: 100mA / DC24V 3. Interface Signal: interface de signal IP, E-BUS signaux INTERFACE 4. Les conditions environnementales: Température de fonctionnement 0 ℃ ~ 45 ℃ Humidité relative 20% ~ 90% Température de stockage -40 ℃ ~ + 55 ℃ humidité relative de stockage de 10% à 93% 5. Dimensions: 110mm × 88mm × 66mm 6. Poids: 0,25 kg quatre, Présentation Description Lorsque ① Puissance et la lumière inhabituelle, lorsque le module de travailler, clignote une fois par seconde (clignotement lent), situation anormale, le voyant clignote une fois (flash) toutes les 250ms. ② interface réseau RJ45, via un cable UTP ou de connecter l'ordinateur directement connecté au routeur. ③ DC +, DATA +, DATA-, COM 485 bus définitions de signal de la borne de raccordement et de la correspondance entre le 485-cablé pour: DC + (+ 24V) → brun, orange Data + (le signal +) → bleu, DATA- vert (le signal - ) → bleu, vert et blanc COM (Common) → marron blanc, orange et blanc de cinq, l'installation et connexion 1. conditions d'installation à ventiler emplacement d'installation, faites attention à l'humidité, aux chocs et à la poussière. 2. L RJ45 cablage de cable spécifications: Le l 485 cables de bus de cinq lignes: 3 ultra-cinq lignes. Des systèmes typiques sont généralement connectés au système est reliée au module (élément de référence), comme illustré ci-dessous. Relié au panneau de commande, les serveurs de gestion du système et d'autres équipements peuvent être atteints commande de commutateur, contr?le d'éclairage (y compris le contr?le de la scène, etc.), la gestion du système, et la connexion avec d'autres systèmes de contr?le et ainsi de suite. Six, les fonctions et les instructions IP module par défaut:, Masque: Passerelle: mise en scène et les paramètres de synchronisation, la synchronisation de réseau et d'autres fonctionnalités, le module besoins grace à son interface réseau pour se connecter à un ordinateur ou un terminal sans fil, via le logiciel de contr?le peut être réglé. L'utilisation sécuritaire et l'entretien de détail 1. Lisez toutes les instructions avant utilisation. 2. Ne fermez pas à l'équipement de brouillage. 3. établir un bon environnement de ventilation. 4. Pendant l'utilisation, faites attention à l'humidité, aux chocs et à la poussière. 5. Lorsque la machine échoue, contactez un personnel qualifié de service ou de la Société. TPW24.5.1 module de puissance du système de TPW24.5.1 manuel qui utilise rail de 35mm de montage standard. 220V AC entrée, sortie 24VDC. Le module d'alimentation prend en charge double alimentation redondante. Et chaque module d'alimentation comporte une sortie de relais peut être utilisé pour détecter la qualité du module d'alimentation. Tout d'abord, les paramètres techniques de l'220VAC de tension de travail ± 10% de la tension de sortie de 24VDC, 50W Température de fonctionnement 0 ℃ -45 ℃ Humidité relative de 20% -90%, le relais de sortie 1A, utilisé pour détecter la qualité de deux modules de puissance, instructions de montage 1,35mm montage sur rail . 2, la sortie relais: sortie de tension 24V DC quand il, la sortie du relais est fermé, pas de sortie de 24VDC, sortie relais déconnexion. Les sorties de relais peuvent être utilisés pour détecter la qualité du module d'alimentation. Troisièmement, la fonction LED feux de circulation rouges, module de sortie de 24VDC, br?ler un feu rouge est allumé, la sortie du relais est fermé; si aucune sortie de 24VDC, exécutez la lumière est éteinte, la sortie relais est débranché; comme quand une alimentation externe court-circuitée feux de l'alarme clignotent. Quatrièmement, les instructions de cablage DC +: DC24V bornes de sortie 5,08 enfichables sont COM: 5,08 DC24V sortie négative connecteur de bornier bornes L 7,62 N 7,62 220VAC entrée FireWire ligne zéro entrée G 7,62 fixe sol borne d'entrée de broche de la prise DO + 7,62 relais terminal fixe la sortie DO- 7,62 fixé borne sorties relais V. cablage procédure étape: connexion d'entrée 220VAC AC, G terre. Deuxième étape: DC + et COM connectent autre entrée d'alimentation du module. La troisième étape: DO +, DO- Générique entrée module de DI est utilisé pour détecter la qualité du module d'alimentation. La figure ci-dessous montre le schéma de cablage du module: Deux méthodes de connexion d'alimentation DC + DC + COM COM ...................... Remarques VI 1, la charge maximale du module d'alimentation est 50W, ce qui a attiré l'attention sur le module de charge totale ne peut être supérieure à 50W. 2, les lignes électriques avec une couleur fixe, d'éviter les erreurs, doivent être soigneusement examinés. 3, le module d'alimentation prend en charge double alimentation, lorsqu'un module est endommagé, vous pouvez assurer un approvisionnement continu par un autre module. 4 sorties de relais peuvent être utilisés pour détecter la qualité du module d'alimentation, le système de contr?le d'accès. ST4.16.1 module de commutation intelligente utilise un module de commutation intelligente manuel sur les lignes de ST4.16.1, le bus de communication 485, livré avec la section de contr?le de la scène, qui ont leurs propres relais passer commande manuelle, avec des capacités de programmation et de gestion à distance. Deuxièmement, les caractéristiques 1.4 canaux unité de sortie de relais 2. Le commutateur est livré avec un contr?leur de scène, jusqu'à 128 scènes 3. Chaque boucle dispose d'un délai de protection d'éclairage (0-60 minutes) 4. Chaque boucle a une ouverture partielle retard (0-25 secondes) 5. Chaque commutateur de relais boucle 6. peut être commandé manuellement avec des capacités de programmation et de gestion à distance 7. Redémarrez équipement facultatif a été ouvert scène ou spécifiée scène 8. 9. communiquent par une norme 485 35mm ferroviaire structure de montage Principaux paramètres techniques 1. Tension d'entrée: DC24V consommation d'énergie 2. de bus: 15mA / DC24V 3. circuit de commutation: 4 4. Chaque circuit de commutation maximales actuelles: 16A 5. Relais vie électrique: plus de 60 000 fois (charge résistive) 6. Conditions environnementales: température 0 ℃ ~ 45 ℃ Humidité relative 20% ~ 90% Température de stockage -40 ℃ ~ + 55 ℃ humidité relative de stockage de 10% à 93% 7. Dimensions de fonctionnement: 108mm × 88mm × 66mm 8. Poids: 0,3 kg Quatrièmement, l'apparence et l'aspect de module de schéma de cablage explication est la suivante: ① 1,2,3,4 borne de sortie du circuit de commutation de relais quatre ② indicateur de circuit. 4 LEDs, respectivement, et 4 correspondent au bouton manuel du commutateur, chaque indicateur montre l'état du circuit de commutation correspondante. ③ 1,2,3,4 quatre boutons manuel relais après chaque pression, le relais état avec l'état actuel de la face. ④ Lorsque l'alimentation et de la lumière inhabituelle, lorsque le module fonctionne correctement, le voyant clignote une fois par seconde (clignotement lent), des conditions anormales, le voyant clignote une fois (flash) toutes les 250ms. ⑤ DC +, DATA +, DATA-, COM 485 bus définitions de signal de la borne de raccordement et de la correspondance entre le 485-cablé pour: DC + (+ 24V) → brun, orange Data + (le signal +) → bleu, DATA- vert (le signal - ) → bleu, vert et blanc COM (Common) → blanc, orange et blanc ⑥ brun interface de signal d'incendie. DI, DI + pour l'interface d'entrée du signal d'incendie, DO-, DO + interface de sortie de rétroaction pour le feu. Les deux interfaces sont signal actif, doivent avoir accès externe au pouvoir, di-, DI + permet seulement la gamme de tension d'entrée DC est DC5V-30V; DO-, DO + permet également seulement une gamme de tension d'entrée DC est DC5V-30V, avec conduite relais DC12V, DC24V et d'autres équipements, qui tous deux ne ont pas accès à un signal 220V AC, afin d'éviter d'endommager l'équipement. Quand le feu de signal d'entrée par défaut du système, déclenchant tous les circuits interface ouverte, sortie de retour connecté; lorsque le signal de feu est rétabli, restaurer l'état d'origine du circuit, l'interface de sortie de rétroaction est déconnecté; signaux ci-dessus peuvent être programmés pour déclencher une scène changements. Cinquièmement, installation et connexion 1. conditions d'installation à ventiler emplacement d'installation, faites attention à l'humidité, aux chocs et à la poussière. 2. spécifications de cablage l Ce module relais passer le cable de sortie: cuivre 2.5mm2 cable l 485 cable de bus: le super paire cinq fils ou 4 fils torsadés 3. Des systèmes typiques sont généralement connectés au système est reliée au module (élément de référence), comme illustré ci-dessous. Permet de connecter des dispositifs de commande de commutateur, contr?le d'éclairage (y compris le contr?le de la scène, etc.) via le panneau de contr?le 485, les serveurs de gestion du système, la gestion des systèmes, et la connexion avec d'autres systèmes de contr?le et ainsi de suite. Six, les fonctions et les instructions d'un commutateur de relais de contr?le manuel du module en plus de recevoir un signal externe de commande de commutation, peut également être interrupteur commandé manuellement. 4.1 en faisant fonctionner le circuit de commutation de relais d'emploi, qui permet de contr?ler de 1 à 4 boucles et hors tension. 2, le nombre d'ID d'ordinateur sur le dispositif doit être paramètres "Logiciel de contr?le système SILO", prévues pour voir les instructions du logiciel. 3, Scène jusqu'à 128 scènes, chaque scène est une combinaison de la boucle ensemble. Scène doit passer "le logiciel de contr?le du système de SILO" pour régler, voir les paramètres du logiciel. 4, en boucle ouverte et en boucle ouverte retard de protection retard: Chaque boucle peut être réglé pour activer retard, la boucle de démarrage après que, pour atteindre la boucle uniquement lorsque la valeur de la sortie du retard. Effet sur le retard, tandis que lancer simultanément plusieurs boucles, boucle départ suivi par la valeur de retard pour éviter l'impact de courant à haute tout a commencé. Remarque: sur les valeurs de retard allant de 0,0 à 25,0 secondes. Circuit de retard de protection: Chaque boucle peut être mis en place pour protéger le retard, qui est, quand une sortie de circuit se éteint, afin de protéger la charge, seulement la temporisation de protéger la valeur de la sortie de la boucle ne peut plus être contr?lée. Remarque: Les valeurs de retard de protection allant de 00 à 60 points. Sur la valeur de retard, de protéger la valeur de retard doit être réglé par "logiciel de contr?le du système de SILO", réglez réfléchie instructions. 5. Le champ est mis à courir après (scénarios puissance de valorisation fixés) de redémarrage que le système mis à ouvrir le champ, après le redémarrage de la machine se déroulera la dernière scène quand il est éteint. Après le système est configuré pour le champ spécifié, la machine redémarre, se déroulera la scène spécifiée. Définit par "logiciel de contr?le du système de SILO", ensemble reflètent instructions. Le scénario par défaut ne fonctionne pas après le redémarrage. Utilisation s?re et entretien de l'autobus ne peuvent pas être inférieur à 1,485 16V, sinon le relais ne fonctionne pas. 2. Chaque boucle doit accéder AC220V ~ 240V alimentation à travers le disjoncteur approprié. 3. Afin de garantir l'utilisation de relais, devraient noter les points suivants: l Pour connecter une charge résistive, le courant de chaque boucle de charge peut être jusqu'à 16A. |
Vous êtes le 10258 visiteur
Droit d'auteur © GuangDong ICP No. 10089450, Wenzhou Sheng Tai Electric Co., Ltd. Tous droits réservés.
Support technique: ShenZhen AllWays Technologie Développement Co., Ltd.
AllSources réseau's désistement: La légitimité de l'information de l'entreprise ne s'engage pas à toute responsabilité de garantie